Transportation Studies Show Regulations May Increase Carrier Costs By Up to 82 Percent



Studies from the American Transportation Research Institute and the Specialized Carriers & Rigging Foundation have found that states’ practices for interstate movements of overweight vehicles have considerable financial impacts to carriers and customers and increases cost by up to 82 percent. The findings also point to economic development barriers as a result of circuitous permitted routes.

The studies were commissioned by the Specialized Carriers & Rigging Association and the SC&R Foundation to understand and quantify whether the lack of permit harmonization across the U.S. has resulted in unnecessary financial burdens being placed on carriers and their customers.

“We’ve long suspected that a lack of permit harmonization has had a significant negative economic impact in general and has placed an onerous and problematic financial burden on businesses specifically,” said SC&RA Vice President of Transportation Steven Todd. “Our objective in commissioning the ATRI study was to see if what we suspected was true.”  

The final report issued by ATRI entitled, “Assessing the Cost and Operational Impacts of State Practices for Minimum Quad Axle Weights Granted for Routine Over-Weight Permits,” begins by acknowledging that “the maze of rules and regulations that specialized carriers face in making interstate movements is truly overwhelming. As many states will attest, the basis for some of these regulations are extremely dated, not based on any empirical data or evidence.” It also quickly points out that “the analysis of regulations across states conducted in this research demonstrate that the costs. . . are considerable.” The report underscores this finding by noting “the added costs strictly due to circuitous permitted routes exceeded $1,000.00 for a haul from Wytheville, Va. To Fort Pierce Fla., while these same costs amounted to nearly $2,200.00 for a trip from Shreveport, La. to Kearney, Neb.”

Of note in the SC&R Foundation study is the discovery that, in general, average percentage increase to customers ranged from 45 – 82 percent, per move. Additionally, the average financial increase to customers ranged from $4,245 to $5,440 in aggregate dollars.

This first-of-its-kind ATRI study supports SC&RA UPT2021 initiative, which aims to establish permit harmonization between all 50 states. Two of the primary goals for UPT2021 are to encourage all states to allow minimum weight thresholds for the most common industry configurations, and to analyze and issue permits via automated permit systems, 24-7. More than 30 states presently use systems that auto-issue permits, in some cases greater than 16 feet wide and high and 250,000 gross pounds. The aim is to gain 100 percent compliance across the country by the year 2021.

“These studies, as well as the U.S. Department of Transportation’s Federal Highway Administration’s study, ‘Best Practices in Permitting in Oversize and Overweight Vehicles,’ continue to support our effort with UPT2021,” said Todd. “There is a consensus regarding the safety and efficiency of automated permitting systems and all of this research backs that conclusion.”

Some of the findings of the FHWA study, described by both government officials and industry leaders included:
  • With automated permitting, the average permit turnaround time decreased from several days and hours to just minutes for most routine and some oversized/overweight permits.
  • Nearly all states (30+) that have implemented automated systems report a moderate increase in total permits applications and issuance.
  • Increased automated permit volume has proportionally increased revenues.
  • Accuracy of permits has dramatically improved.
  • A higher percentage of carriers have ordered, obtained, and traveled on state-issued permits following implementation of automated permit systems.
  • Roadway safety for all motorists has improved.
  • The infrastructure integrity, including the maintaining of bridges and overhead structures, has improved.
  • As a result of moving to automated permitting, states are able to achieve staff efficiencies and reduce costs. Fewer people are required or less time is needed to review and process oversized/overweight permits, freeing up employees to handle customer service inquiries.
  • States have more flexibility with internal headcount issues.
For more information on the ATRI and SC&R Foundation final reports or SC&RA’s UPT2021, contact Steven Todd or visit scranet.org/UPT2021.

The Specialized Carriers & Rigging Association (SC&RA) is an international trade association of more than 1,360 members from 46 nations. Members are involved in specialized transportation, machinery moving and erecting, industrial maintenance, millwrighting and crane and rigging operations, manufacturing and rental. SC&RA helps members run more efficient and safer businesses by monitoring and affecting pending legislation and regulatory policies at the state and national levels; researching and reporting on safety concerns and best business practices; and providing four yearly forums where these and other relevant member issues can be advanced.

For further information, contact:
Lisa Grepps, Director, Marketing & Communications
(703) 698-0291
lgrepps@scranet.org

Related Press Releases

Omega Morgan, Fagioli and Barnhart Take Home SC&RA Hauling Job of the Year Awards
SC&R Foundation Announces New Officers
Barnhart, Fagioli, Burkhalter and Emmert International Win Coveted SC&RA Rigging Job of the Year Awa
SC&RA Presents 2019 Crane & Rigging Safety Awards
SC&RA Presents 2019 Transportation Safety Awards